Can't change anything - Printable Version +- GetSimple Support Forum (http://get-simple.info/forums) +-- Forum: GetSimple (http://get-simple.info/forums/forumdisplay.php?fid=3) +--- Forum: General Questions and Problems (http://get-simple.info/forums/forumdisplay.php?fid=16) +--- Thread: Can't change anything (/showthread.php?tid=1331) |
Can't change anything - revvion - 2011-02-22 Whenever I try to change something I get the message "CSRF detected!" I read the other post about this but couldn't find a solution. Debug mode shows no errors. Website health check says all is good. The only thing I can think of is that the host, source forge* , simply doesn't allow the cms to function. So I was wondering if anybody had an idea if this is the case or if it is something else. *As source forge allows a max of chmod 775. **update** Oke so I looked a bit more in the code and as far as I can tell the IP adress with "$_SERVER['REMOTE_ADDR'];" seems to change causing the error. Is there anyway arround this? because i asume manually disabling this protection will cause security issues. Can't change anything - johnflower - 2011-03-30 Hi, I also am getting this message since using getsimple 3. This didn't happen with the previous version. Is there a way around it? Thanks. John Can't change anything - johnflower - 2011-03-30 I disabled the "Innovation Theme Settings" plugin, and the problem seems to have disappeared. Can't change anything - johnflower - 2011-03-30 Nope, I was wrong. The problem persists. It worked for some editing, but when I try to edit page content, it throws this error. Can't change anything - ccagle8 - 2011-03-30 and it's only when you try to change content? You can create new pages just fine? What if you remove lines 19-25 from your /admin/changedata.php file? http://code.google.com/p/get-simple-cms/source/browse/trunk/admin/changedata.php#19 Can't change anything - johnflower - 2011-03-30 Hi Chris, Thanks for your reply. I get the message when I try to create new content too. I shall look at the link you posted, and report back if the problem persists. Can't change anything - johnflower - 2011-03-30 Nope. Still giving me the message. I blanked out line 19-25 with /**/, and uploaded the file, but it still gives me that error. Can't change anything - johnflower - 2011-03-30 The site is windsports[dot]co[dot]za, by the way. I edited one of the components, and the edit went through. The site is hosted on 000webhost.com, for what it's worth. Can't change anything - Connie - 2011-03-30 johnflower Wrote:The site is windsports[dot]co[dot]za, by the way. I edited one of the components, and the edit went through. have a look at data /other/components.xml you can download that and try to edit or replace with a fresh one from the install package hope that helps, Connie Can't change anything - ccagle8 - 2011-03-30 Also, you can try commenting out this line as well: http://code.google.com/p/get-simple-cms/source/browse/trunk/admin/inc/nonce.php#32 Can't change anything - johnflower - 2011-03-30 Chris, I commented out that line. It didn't help. Connie, I'm not sure as to what I should be looking for. I'm pasting the content of the components.xml file below: Code: <?xml version="1.0" encoding="UTF-8"?> Thanks! Can't change anything - johnflower - 2011-04-04 Hi everbody! Anything else I can try? Would like to make GS3 work. Thanks. Can't change anything - kswaby10 - 2011-04-04 Thanks for the example. car gamesfishing gameszombie gamestyping gamesninja gamesamazon couponsiphone casesjenn air grillsilly bandz |